Acrylic Enamel
| SunCryl
(325 Series) Acrylic Enamel |
|
DESCRIPTION |
||
 |
SunCryl 325 Series is a single stage Acrylic Enamel. Add 325C000 or 325C007 hardener to enhance appearance and durability and recoatability | |
COMPONENTS |
||
 |
* SunCryl
325........... Color * 325C000................ Hardener * 325C007................ Enhanced Hardener * 181.......................... Fast Reducer * 182.......................... Medium Reducer * 183.......................... Slow Reducer * 184.......................... Very Slow Reducer |
|
MIXING RATIO |
||
 |
10 - 15% reduction
with 181 - 184 Reducers. With hardener: 8 parts color to 1 part 325C000 or 325C007 (recommended). (8:1:10-15%) |
|
POT LIFE @ 77° F |
||
 |
Indefinite without
hardener 4 Hours with hardener |
|
CLEAN UP |
||
 |
Valspar Refinish 100 Thinner (Check local regulations) | |
ADDITIVES |
||
 |
ACCELERATOR.............
N/A FISHEYE........................... T152 1 oz per gallon. FLEX ADDITIVE.............. N/A NOTE: Do not spray when surface temperature is below 50 °F. |
|
SURFACE PREPARATION |
||
  |
USE
RECOMMENDED UNDERCOAT SYSTEM FOLLOWING RECOMMENDED
PROCEDURES. * Finish sand with 360 - 400 grit wet or dry sandpaper or equivalent. * Mask vehicle thoroughly is panel repairing. |
|
SUBSTRATES |
||
 |
* AquaPrime 9 * 87N * ColorFil 092 * SunFil 92 * SupaFul 96N * VP Series Epoxy Primer * Properly Prepared OEM Finish |
|
APPLICATION |
||
 |
* Spray two to three coats allowing 20 minutes between coats. Do not mist coat. | |
FLASH/DRY TIMES |
||
 |
AIR DRY @ 77
°F Flash between coats...................... 20 Minutes Tape Time without Hardener......... Overnight Tape Time with Hardener.............. Overnight To Deliver........................................ Next Day FORCE DRY Flash before Force Dry................. 20 Minutes Force Dry Time.............................. 30 Minutes @ 130 °F To Tape.......................................... After Cool Down (1 - 2 Hours) To Topcoat..................................... After Cool Down (1 - 2 Hours) |
|
GUN SETUPS |
||
 |
CONVENTIONAL Gravity Feed........................ 1.6mm - 1.8mm Siphon Feed........................ 1.6mm - 1.8mm HVLP Anest Iwata LPH 400.......... 1.6 mm Binks MG1........................... 1.6 mm C.A. Technology.................. 1.4 mm - 1.6 mm Devilbiss GTI........................ 1.4 mm - 1.6 mm Sagola 450G........................ 1.6 mm Sata 95 & 2000.................... 1.4 mm - 1.5 mm AIR PRESSURES Conventional @ Gun --------- PANEL ----------- OVERALL Gravity Feed......................... 30 - 35psi .......... 35 - 40psi Siphon Feed......................... 30 - 45psi .......... 40 - 50psi HVLP @ Cap........................ 6 - 8psi ............... 8 - 10psi |
|
PHYSICAL DATA |
||
| VOC
(Unreduced)................... 4.4 - 4.7
lbs/gallon VOC (Reduced) ...................... 5.0 lbs/gallon Volume Solids........................ 36 - 38% (Average) Theoretical Coverage........... 570 - 606 sq ft per mil per gallon Flash Point.............................. 52 °F |
||
SAFETY |
||
 |
Before using any
Valspar Refinish product, be sure to read all MSDS and
application instructions and warnings. Always wear a
properly fitted air purifying respirator with organic
vapor cartridges and particulate filter or a fresh air
respirator(depending on product selection), eye
protection, gloves and protective clothing during
application and until vapors are exhausted. Do not permit
anyone without protection in the painting area. This
product is intended for use by a professionally trained
painter. Keep out of the reach of children. |